kascerare.blogg.se - Sct x4 power flash programmer 2014 ford fusion forum

#SCT X4 POWER FLASH PROGRAMMER 2014 FORD FUSION FORUM FOR FREE#
#SCT X4 POWER FLASH PROGRAMMER 2014 FORD FUSION FORUM INSTALL#
#SCT X4 POWER FLASH PROGRAMMER 2014 FORD FUSION FORUM SERIAL#
#SCT X4 POWER FLASH PROGRAMMER 2014 FORD FUSION FORUM UPDATE#

Economy Tune Adjusts the octane based tunes to focus more on economy over performance. Towing Tune Adjusts the octane based tunes to focus more on towing over performance. Higher octane will provide higher performance increase. GAS VEHICLE SPECIFIC OPTIONS: Tune Type Performance levels vary by the octane you select. WOT Shift Increase or Decrease the WOT Shift points of each gear individually by MPH. Traction Control On/Off setting disables traction control without using the TCS button. (Not available on all vehicles) Idle Speed Sets idle speed in RPM. (Not available on all vehicles) Tire Size Sets tire size to correct shift patterns/speedo. Axle Ratio Sets axle ratio to correct shift patterns/speedo. Trans Only tune.ĭIESEL & GAS VEHICLE OPTIONS: EGR Delete Removes the check engine light from deleting EGR mechanically. Towing Should be used when towing any significant load. Moderate gain over stock, safe for light towing, under 5,000 lbs. Good for everyday use, racing, or economy but not recommended for any type of towing. SECTION 10: ADJUSTABLE OPTIONS EXPLAINED DIESEL VEHICLE SPECIFIC OPTIONS Performance The most aggressive preloaded diesel tune. On initial setup, you will need to move to Configuration, press the center button, and select your vehicle from a list of data log files. From the Main Menu, scroll to Gauges/Datalog and press the center button on the X4.

#SCT X4 POWER FLASH PROGRAMMER 2014 FORD FUSION FORUM FOR FREE#

NOTE: If you can’t display a specific value from the preloaded config files, you can download Livelink software for free from the SCT website SECTION 9: ON–DEVICE DATA LOGGING 1. Alternatively, click Locate Custom Tunes. Click Browse and locate your custom tunes on your Desktop. Open the SCT Device Updater software and click the Load Custom Tune File button. From your e-mail, save your custom tunes (.cef files) to your computer’s Desktop.

#SCT X4 POWER FLASH PROGRAMMER 2014 FORD FUSION FORUM INSTALL#

SECTION 8: LOADING CUSTOM TUNES Download and install the SCT Device Updater software and Drivers from : 1. (Adjustable Options are vehicle specific. This will take you to Adjustable Options where you will be able to adjust to different performance levels, vehicle characteristics, and options including, but not limited to, speed limiters, axle ratio and tire size. USING PRE-LOADED TUNE FILES Once you follow the first “Key On” prompt, the device will show you a selection of vehicles and engine sizes.

Pre-Loaded Tune Files = Preloaded SCT tunes for use on stock vehicles only.

MAIN MENU PROGRAM VEHICLE GAUGES / DATALOG VEHICLE DIAGNOSTICS VEHICLE INFO DEVICE INFO DEVICE SETTINGS Within Program Vehicle, there are 2-3 selections depending on the state of the vehicle. At this point, the key should be in the ignition, but in the OFF position until prompted to turn key ON. From the Main Menu, select Program Vehicle. The OBDII port is most commonly found within 24” of the steering column under the driver’s side dash.īEGIN PROGRAMMING 1. SECTION 7: PROGRAMMING THE VEHICLE POWERING ON THE X4 To power up your device, using the provided HDMI to OBDII cable, connect to the vehicle’s OBDII port. DEVICE SETTINGS SECTION 6: CHECKING/CLEARING VEHICLE TROUBLE CODES From the Main Menu, select Vehicle Diagnostics. If using a GM vehicle/ device, it will give you the OS Part Numbers. The VIN and if a Ford vehicle/device, it will give you the Strategy. SECTION 5: READING VEHICLE VIN & STRATEGY/OS PART#’S MAIN MENU PROGRAM VEHICLE GAUGES / DATALOG VEHICLE DIAGNOSTICS VEHICLE INFO DEVICE INFO From the Main Menu, select Vehicle Info.

#SCT X4 POWER FLASH PROGRAMMER 2014 FORD FUSION FORUM UPDATE#

Click the “Download Now” button to the left of the listing that reads “SCT X4 Power Flash Programmer Device Update Software.Wait for that program to download, then double click and “Run” the SCTDeviceUpdater.exe file if it does not open automatically. Click “Tech Support” tab at the top of the page. SECTION 4: UPDATING YOUR X4 DEVICE INSTALLING THE UPDATE SOFTWARE NOTE: Make sure the X4 is unplugged from your computer before starting this process. UNLOCKS LEFT: Number of unlocks remaining. TUNE REVISION The version number of your preloaded tunes. FIRMWARE VERSION: This is essentially your device’s operating system.

#SCT X4 POWER FLASH PROGRAMMER 2014 FORD FUSION FORUM SERIAL#

MAIN MENU PROGRAM VEHICLE GAUGES / DATALOG VEHICLE DIAGNOSTICS VEHICLE INFO DEVICE INFO DEVICE SETTINGS Within Device Info, you will find : SERIAL NUMBER: Needed for dealers to create custom tunes for your vehicle and device. INTERNET ACCESS In the unlikely event that technical support is needed, Internet access may be required to troubleshoot. SECTION 2: PRE-INSTALL CHECKLIST BUSINESS HOURS Technical Support is available Monday – Friday between the hours of 9am and 6pm EST and can be contacted via phone at (407) 774-2447 or through live chat at If you need to contact Tech Support, please be sure to have your device with you before initiating contact. SECTION 1: PARTS + CHECKLIST X4 DEVICE MICRO USB™ CABLE HDMI/OBD II CABLE TOOLS NEEDED: Fuse Puller | Voltage Tester | Battery Charger | Pliers